|
 AMSOIL
SE Series Synthetic Ester Compressor Oils/Coolants
are formulated with premium synthetic ester technology.
These high quality, long life fluids last several
times longer in use than mineral-based oils. AMSOIL
SE Series Synthetic Ester Compressor Oils/Coolants
are fully formulated with non-detergent additives
and are designed for use in rotary screw, vane and
reciprocating compressors. SE Series Synthetic Ester
Compressor Oils/Coolants increase operating efficiency,
reducing money spent on energy, repair and maintenance
costs.
AMSOIL SE Series Synthetic
Ester Compressor Oils/Coolants maintain performance
across a wide operating temperature range. The low
pour points, high viscosity indices and lack of
paraffins (wax) make these excellent all season
lubricants. At high temperatures, SE Series Synthetic
Ester Compressor Oils/Coolants form virtually no
carbon, allowing for clean operation. At cold temperatures,
equipment starts easier and the lubricant is quickly
pumped to critical components, preventing lubricant
starvation and excessive wear. SE Series Synthetic
Ester Compressor Oils/Coolants also resist water
to prevent damaging oil/water emulsions, allowing
for longer lubricant life and ease of water removal
from the sump.
PERFORMANCE
FEATURES
-
Resists
foaming
-
Rust
and oxidation inhibited
-
Readily
separates from water
-
Recommended
for use in rotary screw and reciprocating compressors
-
Long-life/extended
drain performance
-
Compatible
with polyglycol fluids such as Sullube 32® and
Ingersoll-Rand SSR Ultra-coolant®
-
SEI
is biodegradable under the CEC-L33-A94 standard
SAFETY
ADVANTAGE
AMSOIL SE Series Synthetic
Ester Compressor Oils/Coolants have higher flash,
fire and auto ignition points than competitive petroleum
oils. Their resistance to carbon formation and the
ashless additive system minimize the incidence of
deposits acting as ignition-promoting hot spots.
Although AMSOIL SE Series increase fire safety,
they cannot be considered non-flammable.
APPLICATION
RECOMMENDATION
AMSOIL
SEI is a multi-viscosity oil meeting the requirements
of 5W-20. It may be used in applications calling
for either an ISO-32 or ISO-46 compressor oil or
coolant. It is recommended for use in single and
multi-stage rotary screw compressors and vacuum
pumps that call for this viscosity.
When
installing AMSOIL SEI, it is recommended that the
old oil be thoroughly drained and if warranted,
the system cleaned. If a lot of carbon or residue
is found on the internal compressor parts, follow
the manufacturer's recommendations for removal prior
to installing the new oil. AMSOIL
SE Series Synthetic Ester Compressor Oils/Coolants
have a high level of solvency and may remove deposits
left in the system. Check the filters and oil/air
separators regularly for the first 500 hours of
operation and replace as necessary.
AMSOIL
SEI is compatible with and recommended as a replacement
for much higher priced polyalkylene glycol (PAG)
compressor oils or coolants such as Sullube 32®
and Ingersoll Rand SSR Ultra Coolant®. No flushing
is necessary when changing over from Glycol Coolants
to AMSOIL SEI. However, draining the system and
changing the filters is recommended.
AMSOIL
SEI is recommended for use up to 8,000+ hours for
most compressor applications. However, this is subject
to operating conditions and maintenance practices.*
Monitoring by oil analysis every 1,000 hours is
recommended.
* Where
discharge temperature exceeds 205°F, lubricant life
expectancy is reduced.
COMPATIBILITY
AMSOIL
SEI is compatible with petroleum oils, most synthetic
oils*, and many seals, paints and materials commonly
used in compressors. Materials recommended and not
recommended for use with SEI oils/coolants are listed
below. For additional information, see the AMSOIL
Compatibility Guide (G-1274) or consult your AMSOIL
Dealer or AMSOIL INC.
*AMSOIL
SE Series is NOT RECOMMENDED as a replacement or
for use with the silicone based compressor oil Sullube
24KT®. AMSOIL SE Series is NOT RECOMMENDED for use
in "Breathing Air or Refrigeration" compressors.
RECOMMENDED
Seals
- Viton®, High Nitrile Buna N (>36%), Teflon®
Paints - Epoxy, Oil-Resistant Alkyd, Two-Part
Urethane
Plastics - Nylon, Delrin®, Celcon®, PBT
NOT
RECOMMENDED
Seals
- Neoprene, SBR Rubber, Low Nitrile Buna N
Paints - Acrylic Paint, Lacquer
Plastics - Polystyrene, Polycarbonate Plastic,
PVC, ABS
NOTE:
Process gasses suitable for use with the SE
Series:
Nitrogen,
hydrogen, helium, carbon monixide, carbon dioxide
(dry), ethylene, methane, propane, butane, propylene,
butylene, natural gas, benzene, butadiene, furnace
(crack gas), hydrogen sulfide (dry), sulfur hexafluoride,
synthetic gas, sulfur dioxide.
AMSOIL PRODUCT
AVAILABILITY
AMSOIL
SE Series is available in 5-gallon pails, 55-gallon
drums, 275-gallon totes, and bulk quantities. For
275-gallon totes, please allow two to four weeks
for delivery.
Sullube
32®
and
Sullube 24KT®
are
trademarks of the Sullair Corporation. Ingersoll-Rand
SSR Ultra-Coolant®
is
a trademark of Ingersoll-Rand, Inc.
|
